Bently Nevada 330102-00-40-10-02-00 3300 XL 8 mm Probe – PPS Tip

Description Product Overview Bently Nevada 330102-00-40-10-02-00 is a 3300 XL 8 mm Proximity Probe. It measures radial vibration and position in turbines, compressors, and pumps. The probe uses a PPS tip and stainless steel case. This model includes armor, a 1.0 meter cable, and a miniature coaxial ClickLoc connector. Operating range is -52°C to 177°C. It supports hazardous area installations with Ex ia and nA approvals. For inquiries: 86 158 8020 0923 (WhatsApp) Key Technical Data Brand: Bently Nevada Model Number: 330102-00-40-10-02-00 Series: 3300 XL Type: 8 mm Proximity Probe Linear Range: 2 mm (80 mils) from 0.25 to 2.3 mm Recommended Gap (Radial Vibration): -9 Vdc (~1.27 mm / 50 mils) DC Resistance (1.0 m length): 7.59 ± 0.50 Ω Temperature Range (Standard Probe): -52°C to 177°C Probe Tip Material: Polyphenylene sulfide (PPS) Probe Case Material: AISI 303 or 304 stainless steel Thread Size: 3/8-24 UNF Max Thread Engagement: 0.563 inch Humidity Test: Measurement & Performance Frequency Response: Reliable signal with field wiring up to 305 meters. See rolloff graphs for high frequencies. Resolution: High resolution for vibration and position monitoring. Linearity: Linear output from -1 to -17 Vdc over 2 mm range. Environmental Tolerance: Withstands humidity per IEC 68-2-3. Noise Immunity: Works with shielded triad cable for low noise. Installation Guide Use 0.2 to 1.5 mm² (16-24 AWG) tinned field wiring. Recommended cable: 3-conductor shielded triad. Max wire length between sensor and monitor: 305 m (1000 ft). Do not expose probe below -34°C often. It may damage the pressure seal. Thread engagement max: 0.563 inch. Torque and gap setting: Set to -9 Vdc for radial vibration. Compatibility Works with 3300 XL Proximitor Sensor. Use intrinsic safety barriers (drawing 141092) or galvanic isolators. Non-incendive circuit connection per drawing 140979. Compatible with monitors accepting 3300 XL probes. 3300 XL 11 mm Proximity Probes also available. Certifications Ex ia IIC T5…T1 Ga (Class I, Zone 0; Class I, Div 1, Groups A, B, C, D; Class II, III) Ex nA IIC T5…T1 Gc (Class I, Zone 2; Class I, Div 2, Groups A, B, C, D) Ex ec IIC T5…T1 Gc (Class I, Zone 2) Temperature class T5 (ambient -55°C to 40°C) up to T1 (-55°C to 232°C) for EPL Ga/Gc. For EPL Dc: T280°C at Ta up to 232°C down to T90°C at 40°C. Agency Approval Option: 00 = Not required (customer specified). Maintenance & Service No routine calibration needed. Factory sealed. Check cable and connector for damage before each use. Pressure seal not factory tested. Contact custom design if needed. Easy replacement: same thread and length options. Typical Applications & Diagnostics Applications: Steam turbines, gas turbines, centrifugal compressors, fans, pumps, generators, and motors. Diagnostic ability: Detects shaft vibration, axial position, and eccentricity. Helps predict bearing wear, unbalance, and misalignment. Connects to PLCs, DCS, or condition monitoring systems for real-time alerts. Package Contents 1 x 3300 XL 8 mm Probe (PPS tip, armored, 3/8-24 thread) Cable length: 1.0 meter with miniature coaxial ClickLoc connector Installation manual (digital copy) No agency approval certificate included (option 00) Warranty & Shipping Warranty: 12 months against manufacturing defects. Shipping carriers: FedEx, UPS, DHL. Fast global delivery. Frequently Asked Questions (FAQ) What is the linear range of this probe? 2 mm (80 mils). Starts at 0.25 mm from target. Can I use this probe in high temperature? Yes. Standard tip works up to 177°C. Extended range up to 218°C (tip). Does the probe work with 3300 XL 11 mm models? No. The 8 mm probe is separate. See 11 mm series here. What happens below -34°C? Pressure seal may fail early. Keep above -34°C for reliability. How do I select the correct probe length? Check your thread depth and cable distance. Use unthreaded length 00 (0 in), case length 4.0 in, total cable 1.0 m. Can I cut the cable? No. Cutting changes resistance and calibration. Order custom length instead. Which connector type is this? Miniature coaxial ClickLoc connector, standard cable. Option code 02. Do you have stock for emergency orders? Yes. Contact 86 158 8020 0923 via WhatsApp for fast shipment. Why is the pressure seal not tested? Standard units skip test to reduce cost. Request custom testing if needed. Buying Guide Match probe thread (3/8-24 UNF) to your mounting hole. Select total cable length: 1.0 m for short runs. Longer? Use extension cable. Need hazardous area? Choose Ex ia version with barriers. For high vibration or high temp, confirm T-class and ambient range. Always pair with 3300 XL Proximitor Sensor for correct output. New to Bently Nevada? Start with 8 mm probe for standard machines. Upgrade to 11 mm probes for larger gap or rough surfaces. Copyright © 2026 PLCDCS HUB Limited. All rights reserved. Original Source: https://plcdcshub.com/ Partner: Powergear X Automation Limited Oiltech Controls Limited